Skip to main content

DC MOTOR INTERVIEW QUESTIONS & ANSWERS

DC motor is one of the rotary machines which makes use of electrical current and converts it to mechanical energy which can be used in many other functions or operations. The forces are generated by magnetic fields. Do search in wisdom jobs for DC motor job listings for full time and part time positions updated today. If you are looking for job then go check out interview questions page to get more information on the kind and level of questions you will come across during the interview. Various jobs were present in all over India for this technology which is in high demand. Wisdomjobs DC motor interview questions and answers provides you with complete guide on the DC motor and prepares you for winning job interview.

Question 1. What Is The Principle Of Operation Of A D.c Motor?

Answer :

The operation of a D.C Motor based on the principle that when a current carrying conductor is placed in a magnetic field, the conductor experiences a mechanical force. Basically, there is no constructional difference between a d.c. motor and a d.c generator. The same d.c. machine can be run as a generator or motor.

Question 2. What Is Back E.m.f Or Counter E.m.f?

Answer :

When the armature of a d.c. motor rotates under the influence of the driving torque, the armature conductors move through the magnetic field and hence e.m.f. is induced in them as in a generator. The induced e.m.f. acts in opposite direction to the applied voltage V (Lenz’s law) and in known as back or counter e.m.f Eb. It is always less than the applied voltage V, although this difference is small when the motor is running under normal conditions.

Question 3. What Is Speed Regulation?

Answer :

Speed regulation is the change in speed when the load on the motor is reduced from rated value to zero. It is expressed as a percentage of rated load speed.

Question 4. Why Series Motor Cannot Be Started On No-load?

Answer :

Series motor cannot be started without load because of high starting torque. Series motor are used in Trains, Crane etc.

Question 5. Which Type Of Motor Is Used In Trains, What Is The Rating Of Supply Used?

Answer :

Dc series is in the used in trains to get high starting torque while starting of the trains and the operating voltage is 1500v dc.

Question 6. Explain Different Methods Of Speed Control Of D.c Shunt Motors?

Answer :

Speed control of a d.c shunt motor can be done using:

Flux control method ()
Armature control method
Voltage control method
Question 7. Explain Different Methods Of Speed Control Of D.c Series Motors?

Answer :

Speed control of a d.c series motor can be done using:

flux control method
Armature-resistance control control method
Question 8. Why Is The Starting Current High In A Dc Motor (or) Why Do We Use A Starter?

Answer :

For DC motors, Voltage equation is

V=Eb-IaRa

Where V = Terminal voltage,

Eb = Back emf in Motor

Ia = Armature current

Ra = Aramture resistance.

At starting, Eb is zero. Therefore, V=IaRa, Ia = V/Ra, where Ra is very less like 0.01ohm.i.e, Ia will become enormously increased. The excessive current will damage commutator and brushes and eventually blow out the fuses.

Question 9. How Can You Reverse The Direction Of Rotation Of A D.c Motor?

Answer :

We can reverse the direction of rotation of a D.C Motor by either reversing the field current or armature current. If both the currents are reversed the motor will run in original direction.

Question 10. Why The Field Of A D.c Shunt Motor Should Not Be Open?

Answer :

The shunt motor will achieve dangerously high speed and may destroy itself.

Question 11. What Will Happen If The Direction Of Current At The Terminals Of A D.c Motor Is Reversed?

Answer :

The direction of rotation of motor remains the same as current in armature and field.

Question 12. What Happens When A D.c Motor Is Connected Across An A.c Supply?

Answer :

The motor will run but it would not carry same load as it would on d.c supply.
More sparking at the brushes
Eddy currents will be high and will cause overheating and may eventually burn on a.c supply
Question 13. Mention The Methods For Starting An Induction Motor?

Answer :

DOL – direct online starter
Star delta starter
Auto transformer starter
Resistance starter
Series reactor starter
Question 14. What Are The Types Of Starters Used For Starting Of D.c Motors?

Answer :

There are two principal types of d.c. motor starters viz., three-point starter and four-point starter. As we shall see, the two types of starters differ only in the manner in which the no-volt release coil is connected.

Question 15. What Are The Advantages Of Star-delta Starter With Induction Motor?

Answer :

The main advantage of using the star delta starter is reduction of current during the starting of the motor. Starting current is reduced to 3-4 times of current of Direct online starting. As the starting current is reduced, the voltage drops during the starting of motor in systems are reduced.

Question 16. What Are The Different Tests Conducted On D.c Machines?

Answer :

Brake test
Swinburne’s test or No-load test
Regeneration test or Hopkinson’s test
Retardation or Running down test
Question 17. Why Is Swinburne’s Test Conducted?

Answer :

Swinburne’s test is conducted at No-load condition to predetermine the efficiency at different loads and to measure the losses separately.

Comments

Popular posts from this blog

Stabilizer in Hindi स्टेबलाइजर की पूरी जानकारी हिंदी में

स्टेबलाइजर क्या होता है घर के लिए सही वोल्टेज स्टेबलाइजर आपने वोल्टेज स्टेबलाइजर के बारे में जरूर सुना होगा और आपके घर में stabilizer जरूर होगा। लेकिन क्या आप जानते हैं कि स्टेबलाइजर क्या होता है?(what is stabilizer ?) क्या आप जानते हैं कि स्टेबलाइजर का काम क्या है और स्टेबलाइजर कितने प्रकार के होता है? क्या आप जानते हैं कि स्टेबलाइजर कैसे काम करता है? यदि नहीं जानते हैं तो हमारा ये पोस्ट जरूर पढ़ें। इस पोस्ट में आज हम स्टेबलाइजर की पूरी जानकारी हिंदी(stabilizer in Hindi) में देने जा रहे हैं। स्टेबलाइजर एक ऐसी डिवाइस होती है जो कि Fix Value की वोल्टेज प्रदान करता है.हमारे घर में कुछ ऐसे उपकरण होते हैं जिन्हें कम से कम 240 V की सप्लाई की जरूरत होती है और कुछ कारणवश हमारे घर में अगर सप्लाई 240V से कम आती है तो वह उपकरण ठीक प्रकार से कार्य नहीं कर पाता इसीलिए उसके लिए स्टेबलाइजर की जरूरत पड़ती है. जो कि हमारे घर में आने वाली सप्लाई को 240V पर Fix कर के उपकरण को 240V की सप्लाई प्रदान करता है. स्टेबलाइजर का इस्तेमाल ज्यादातर रेफ्रिजरेटर  (फ्रिज) एयर कंडीशनर इत्यादि पर किया जाता है.

Star Delta Starter In Hindi | स्टार डेल्टा स्टार्टर | का प्रयोग मोटर में क्यों किया जाता है ?

स्टार डेल्टा स्टार्टर |Star Delta Starter इस Article मे स्टार डेल्टा कनेक्शन, Star Delta Formula, स्टार डेल्टा स्टार्टर का सिद्धांत, पावर डायग्राम, कन्ट्रोल डायग्राम, स्टार डेल्टा स्टार्टर के लाभ एवम नुकशान और स्टार डेल्टा स्टार्टर से संबधित इंटरव्यू में पूछे जाने वाले सवाल पे भी विस्तृत में जानकारी देने की कोशिश की हे। आशा हे आप के लिए मददगार होगी। Star Delta Starter मोटर को सलामती पूर्वक चालू करने के लिए, मोटर का रक्षण करने के लिए एवम मोटर का स्टार्टिंग करंट कम करने के लिए उपयोग किया जाता हे। मोटर को स्टार्ट करने के लिए और भी कही टाइप के स्टार्टर हे। जैसे की डायरेक्ट ऑन लाइन स्टार्टर, स्टार डेल्टा स्टार्टर, ऑटो ट्रांसफार्मर स्टार्टर, सॉफ्ट स्टार्टर, vfd (Variable Frequency Drive) और रोटर रेजिस्टेंस स्टार्टर, जो मोटर को सलामती पूर्वक चालू भी करते हे,और सुरक्षा भी प्रदान करते हे। स्टार डेल्टा स्टार्टर क्या है? एक स्टार्टर का काम हे स्टार्ट करना। यहां एक इलेक्ट्रिक मोटर स्टार्टर की बात हे। स्टार डेल्टा स्टार्टर याने, एक इलेक्ट्रिकल उपकरण जो कही उपकरणों को एकत्रित करके तैयार किया जाता ह

वायर जॉइंट के Different प्रकार

 Different Types of Wire Joint Requirement:- किसी भी तार में जॉइंट बनाने की जरुरत क्यों पड़ती है किसी भी वायर में जॉइंट बनाने की जरुरत इसलिए पड़ती है ताकि किसी भी चालक तार की लम्बाई बढ़ाई जा सके और किसी चालक लाइन में से किसी अन्य लाइन को जॉइंट बनाकर उसे स्थाई रूप से जोड़ा जा सके जॉइंट ऐसा होना चाहिए की वह लाइन को अच्छे कनेक्ट तथा लाइन को पर्याप्त सुद्रढ़ता भी प्रदान कर सके,,इन जोइन्टो को विभिन्न प्रकार से तैयार किया जाता है यह चालक तार की मोटाई,जोड़ की किस्म,जॉइंट किस लाइन में लगाना है इत्यादि पर निर्भर करती है  ।   Different Types of  Joints:-ओवर हेड लाइन्स तथा घरेलु वायरिंग में मुख्यतः निम्न जोड़ प्रचलित है  Twisted Joint(ऐंठा हुआ जोड़) :- इस प्रकार के जॉइंट में तारो अथवा केबल के चालक सिरों को आपस में ऐंठ कर उनके अंतिम समापन सिरों को जोड़ की और मोड़ देते है इस प्रकार का जॉइंट ओवर हेड लाइन में खम्बो के ऊपर लगे इंसुलेटर पर लगाया जाता है इसे किसी लाइन के मध्य में नहीं लगाया जाता है इसे Pig Tail अथवा Rat-Tail Joint जॉइंट भी कहते है।    Married Joint(मैरीड जॉइंट) :- इस प्रकार के जॉइंट में तारो अथ